Microchip
Niet gecategoriseerd
PIC18F6680
Microchip PIC18F6680 Handleiding
Hier is de Microchip PIC18F6680 (Niet gecategoriseerd) gebruikershandleiding. 38 pagina's in taal Engels met een gewicht van 3.8 Mb. Als u geen antwoorden op uw probleem kunt vinden Vraag het onze community.
Pagina 1/38
2010 Microchip Technology Inc. DS39606E-page 1
PIC18FXX80/XX85
1.0 DEVICE OVERVIEW
This document includes the programming
specifications for the following devices:
2.0 PROGRAMMING OVERVIEW
PIC18FXX80/XX85 devices can be programmed using
either the high-voltage In-Circuit Serial ProgrammingTM
(ICSPTM) method, or the low-voltage ICSP method.
Both of these programming methods can be done with
the device in the user’s system. The low-voltage ICSP
method is slightly different than the high-voltage
method, and these differences are noted where appli-
cable. This programming specification applies to
PIC18FXX80/XX85 devices in all package types.
2.1 Hardware Requirements
2.1.1 HIGH-VOLTAGE ICSP
PROGRAMMING
In High-Voltage ICSP mode, these devices require two
programmable power supplies: one for VDD and one for
MCLR/VPP. Both supplies should have a minimum
resolution of 0.25V. Refer to Section 6.0 “AC/DC
Characteristics Timing Requirements for Program/
Verify Test Mode” for additional hardware parameters.
2.1.2 LOW-VOLTAGE ICSP
PROGRAMMING
In Low-Voltage ICSP mode, these devices can be pro-
grammed using a VDD source in the operating range.
This only means that MCLR/VPP does not have to be
brought to a different voltage but can instead be left at the
normal operating voltage. Refer to Section 6.0 “AC/DC
Characteristics Timing Requirements for Program/
Verify Test Mode” for additional hardware parameters.
2.2 Pin Diagrams
The pin diagrams for the PIC18FXX80/XX85 family are
shown in Figure 2-1, Figure 2-2 and Figure 2-3. The
pin descriptions of these diagrams do not represent the
complete functionality of the device types. Users
should refer to the appropriate device data sheet for
complete pin descriptions.
TABLE 2-1: PIN DESCRIPTIONS (DURING PROGRAMMING): PIC18FXX80/XX85
• PIC18F6585 • PIC18F6680
• PIC18F8585 • PIC18F8680
Pin Name
During Programming
Pin Name Pin Type Pin Description
MCLR/VPP/RA5 VPP P Programming Enable
VDD(2) VDD P Power Supply
VSS(2) VSS P Ground
AVDD(2) AVDD P Analog Power Supply
AVSS(2) AVSS P Analog Ground
RB5 PGM I Low-Voltage ICSP™ Input when LVP Configuration bit equals ‘1’ (1)
RB6 PGC I Serial Clock
RB7 PGD I/O Serial Data
OSC1 OSC1 I Oscillator Input (needs to be pulled high during programming.)
Legend: I = Input, O = Output, P = Power
Note 1: See Section 5.3 “Low-Voltage Programming (LVP) Bit” for more detail.
2: All power supplies and ground must be connected.
Flash Microcontroller Programming Specification
Probleemoplossing Microchip PIC18F6680
Als je de handleiding al zorgvuldig hebt gelezen maar geen oplossing voor je probleem hebt gevonden, vraag dan andere gebruikers om hulp
Specificaties
| Merk: | Microchip |
| Categorie: | Niet gecategoriseerd |
| Model: | PIC18F6680 |