Mikrotik PowerBox Handleiding
Hier is de Mikrotik PowerBox (Router) gebruikershandleiding. 4 pagina's in taal Engels met een gewicht van 0.5 Mb. Als u geen antwoorden op uw probleem kunt vinden Vraag het onze community.
Pagina 1/4
RouterBOARD PowerBOX
Quick Setup Guide and Warranty Information
The PowerBOX (product code RB750P-PBr2) is an outdoor device with five ethernet ports. Ports 2-5
support passive PoE output for powering other devices.
First use
Connect your WAN cable to port 1, and LAN computers to ports 2-5
Set LAN computer IP configuration to automatic (DHCP)
The default IP address from LAN is 192.168.88.1
Powering
The board accepts powering from the power jack or from the first Ethernet port (Passive PoE):
direct-input power jack (5.5mm outside and 2mm inside, female, pin positive plug)
accepts 8-30V DC
first Ethernet port accepts passive Power over Ethernet accepts 8-30V DC
The power consumption of this device is 2W under maximum load.
Power output
This device can supply PoE powering to external devices from its Ethernet ports. This is convenient as
you don't need any additional PoE injectors to power other devices. This feature is indicated by the
letter “P” in the device model name. The output Voltage will be the same as input Voltage, and this
feature will have to be enabled on the specific ports in RouterOS software. By default it is disabled.
Maximum power output of each ethernet port in this mode is 1A (2A total for all ports). Once Power
Output is enabled in RouterOS, the Ethernet LED light shines also in red. Read LED means the port is
currently providing PoE power, green means Ethernet has link, both at the same time means Ethernet
is linked and power is being output.
Booting process
This device doesn't come fitted with a Serial Port connector, so initial connection has to be done via the
Ethernet cable, using the MikroTik Winbox utility. Winbox should be used to connect to the default IP
address of with the username and no password.192.168.88.1 admin
In case IP connection is not available, Winbox can also be used to connect to the MAC address of the
device. More information here: http://wiki.mikrotik.com/wiki/First_time_startup
In case you wish to boot the device from network, for example to use MikroTik Netinstall, hold the
RESET button of the device when starting it until the “ACT” LED light turns off, and the PowerBox will
start to look for Netinstall servers.
Extension Slots and Ports
Five individual Ethernet ports, supporting automatic cross/straight cable correction (Auto
MDI/X), so you can use either straight or cross-over cables for connecting to other network
devices. The Ethernet port accepts 8-30V DC powering from a passive PoE injector, 12V or more
is recommended to compensate for loss in cables.
www.routerboard.com 1 05/11/15
Probleemoplossing Mikrotik PowerBox
Als je de handleiding al zorgvuldig hebt gelezen maar geen oplossing voor je probleem hebt gevonden, vraag dan andere gebruikers om hulp
Specificaties
| Kleur van het product: | Wit |
| Gewicht: | - g |
| Breedte: | 125 mm |
| Diepte: | 178 mm |
| Hoogte: | 48 mm |
| Ethernet LAN: | Ja |
| Inclusief AC-adapter: | Ja |
| Aantal Ethernet LAN (RJ-45)-poorten: | 5 |
| Aansluiting voor netstroomadapter: | Ja |
| Intern geheugen: | 64 MB |
| Bekabelingstechnologie: | 10/100Base-T(X) |
| Ethernet WAN: | Ja |
| Flash memory: | 16 MB |
| Ethernet interface type: | Fast Ethernet |
| Power over Ethernet (PoE): | Ja |
| Stroomverbruik (typisch): | 2 W |
| Bedrijfstemperatuur (T-T): | -35 - 70 °C |